Off-grid setup guide
A small off-grid mesh radio paired with your phone can send text messages for miles with no cell towers, Wi-Fi or power grid. Here is how to set one up before you need it. Every step links to the official documentation of the open-source mesh project.
What it is
These radios run free, open-source mesh firmware (credited in our Acknowledgments). Each radio pairs with a phone or computer and relays messages for the others, so a group of radios forms a mesh: a message hops from node to node (3 hops by default, up to 7) until it reaches everyone. It needs no cell service, internet or license for normal use. It sends short text, positions and sensor readings, not voice. Sources: Introduction, Mesh algorithm, Radio configuration.
Hardware
Pick a supported board from the official supported devices list. The common types:
- Ready-made handhelds with a case, battery and screen: easiest for families. Pair one with each phone.
- Development boards (for example Heltec, LILYGO, RAK WisBlock): cheaper, but you add a case, battery and antenna.
- Solar nodes: a weatherproof board, battery and panel for a roof or pole, to extend range for the whole neighborhood.
Buy the 915 MHz (US) version and a proper antenna for that band. Never power on a radio without its antenna attached. Height matters more than power: a node in an attic, on a roof or on a hill reaches far more people. See Antennas and Flashing firmware (the web flasher works in Chrome or Edge).
US 915 MHz band
In the United States, set the radio's region to US. That uses the 902–928 MHz band, with no duty-cycle limit and a 30 dBm (1 W) power cap in the firmware's region table. A new radio with the region left unset will not transmit at all, so this is the first setting to change. Every radio in your group needs the same region and the same modem preset (the default is LongFast). Sources: Radio configuration: Region, Radio settings and presets.
App setup
- Install the official app: iPhone / iPad / Mac, Android, or use the web client in Chrome or Edge.
- Turn the radio on and pair it over Bluetooth from the app (the radio's screen or the app shows the PIN).
- Set Region: US and leave the preset on LongFast unless your local group uses another one.
- Set your long and short name, and keep the role on CLIENT (or CLIENT_MUTE for a second radio indoors).
- Decide how precise your shared position should be before you go out (see Channels below).
Sources: Getting started, Initial configuration, Configuration tips: roles.
Channels
Each radio has up to 8 channels. Channel 0, the primary, defaults to the public LongFast channel with a well-known key, so anyone nearby with default settings can read it. That is good for meeting neighbors and for public calls for help, but not for private messages.
- Create a secondary channel with its own random key for your family or group, then share it by QR code or link from the app.
- Only scan channel QR codes from people you trust: a QR code can also change your radio's mesh settings.
- Your position is shared on the primary channel. Lower the position precision, or turn position sharing off, if you do not want your home location on the public channel.
Sources: Channel configuration, FAQ: sharing a channel, Position configuration, Configuration tips.
Power and solar
Most boards run for a day or more on an 18650 or LiPo cell and charge from USB, so a USB power bank or a small folding solar panel keeps a handheld going. For a fixed node, use a weatherproof box, a battery sized for several cloudy days and a panel sized for winter sun. The radio's power-saving setting turns off Bluetooth, USB serial, Wi-Fi and the screen to stretch a small battery or solar supply, so use it only on a fixed relay node, not on the radio you pair with your phone. Sources: Power configuration, Supported devices.
Etiquette
- Keep the role on CLIENT. Do not use ROUTER or REPEATER unless your local group agrees: extra routers cause collisions and shrink the mesh.
- Keep messages short and do not repeat them. Every message uses airtime that everyone shares.
- Leave the hop limit at 3 unless your area really needs more.
- Do not set very short position or telemetry intervals; the defaults are chosen to keep the channel clear.
- Do not send private details on the public LongFast channel.
Legal: unlicensed vs. ham
Unlicensed (default): in the US, the firmware runs in the 902–928 MHz ISM band with no license, within the firmware's region power limits and using legal antennas for your device. Encryption is allowed in this mode.
Licensed amateur (ham) mode: a licensed operator can turn on the licensed setting with their call sign as the long name. The official FAQ notes this allows more transmit power in the US (up to 10 W, 47 CFR 97.313(j)) and higher-gain antennas, but encryption is not allowed (FCC Part 97.113(a)(4)), the call sign is sent at least every 10 minutes (Part 97.119(a)), and licensed and unlicensed nodes cannot talk to each other. Sources: FAQ: Amateur radio (ham), User configuration, Project legal notes.
This is general information, not legal advice. Check the current FCC rules for your setup.
Before the grid goes down
- Set up every radio now, while you still have internet for firmware and app updates.
- Agree on a private channel and a check-in time with your family or group, and practice once a month.
- Charge everything, keep a power bank and a small solar panel with the radios, and label which radio is whose.
- Find your local mesh group and see who is already on the air near you on our mesh map.
- Write down the basics (region US, preset, channel name) on paper in case a radio needs a reset.
This guide is independent and links to the official project documentation. We do not sell radios or use affiliate links. Credits